LG
How To: Whirlpool/KitchenAid/Maytag Washer Lid Lock
How To: Whirlpool/KitchenAid/Maytag Washer Lid Lock Assembly W11307244
#WhirlpoolKitchenAidMaytag #Washer #Lid #Lock
“AppliancePartsPros”
How To Replace: Whirlpool/KitchenAid/Maytag Washer Lid Lock Assembly W11307244 …
source
To see the full content, share this page by clicking one of the buttons below |
The only thing you could have told us is fact that when you push the top section to the front the hooks holding this section has two hooks on each side and you have to move it around till it unhooks. It took me a while to get it up and then was able to use my strap with hooks to hold the section vertical, the one with the lid. Thanks I got my switch installed.
I replaced the lid lock. My biggest problem was to get the old one out. Getting the new one in was much easier.
Thank you so much I was bout to junk my washer I’m so glad I found you ❤
I will try the replacement tomorrow. After looking at several other videos I can understand everything you did and your video more closely resembles my washer. I believe I can do this replacement now.
So you say that the lid will close once you plug it in… what if it doesn't close once plugged in? What do I do then?
I replaced the part but the lock lid light did not light up or lock when I went to wash
Don’t you have to recalibrate it after
Thank you for being specific on how to remove lid lock on top of washer. another site said it needed 1/4 in screws, which this, MINE, doesn't. Thanks!
Thanks you made it so so easy to mix my washer great video great job 5 stars
Simon, help me please. the top of my washer will only slide 1/4 inch. The back of the top can be picked up, but I can't fix it ththis way. What can I do?
These people and their safety bull crap… They do it to control you and make you accept the control. In 30 years I’ve never heard of a kid taking a spin in a laundry washer. Now all of a sudden this is a problem… My kid lock broke and I couldn’t use my 1500 dollar washer and they wanted 130 bucks for the part. Well Whirlpool can go fish! I bypassed their bs switch. Soon they will make us store kitchen knives in a gun safe or some crap. How about all the EMI and RF radiation emitted by the smart meters and all the wi-fi washing machines talking with the smart meter? All that must be all safe. lol
If the lid still won't unlock after you plug it in;
Unplug it, reach down into the lid latch hole, press and hold the small white tab on the left, and then try plugging it in again. It should unlock after a few seconds. Figure it's worth mentioning since I thought mine was broken at first because it wouldn't unlock lol
Thank you!!!! I was able to fix my washing machine without spending hundreds on a repair person. ❤❤❤
Simon. This was the easiest repair ever! Best repair video ever. Thorough and easily understandable! Bravo!
Thank you so much 😊 I was able to successfully replace my lid lock mechanism very easily with your impeccable instructions 😊
I replaced the lid switch…… no problem. But after, the lid won't unlock. How do I correct this?
Thanks for a perfectly clear demonstration. But I'm not washing yet. The part came locked and the lid won't close. I tried hitting reset, and unplugging, but no success. The "lid locked" light is lit. Is there anything I can do to unlock the part to allow the lid to close?
I have a maytag. Put the top in the up pos like he shows and pop the metal pins on the switch panel underneath w a flathead pushing down. Careful the switch panel is connected. Then u can access the pin.
Thank you Sir! I had a extra step of course on mine. I had to take off the switch panel to be able to access pin but great video thx again
You make this look so easy! I'm doing this tomorrow on my washer and hope it goes as smooth as it does with you. !!
Thank you so much. Your a life saver.
I've had to replace it 2xs in 3 months. What's causing them to go or should I chalk it up to a bad replacement part?
I was going insane trying to figure out how to remove the lock from the washer. Thanks so much. You saved me!
Thank you so very much.
I live in a rural area.
I ordered the part, watched your video 4x, and changed it out myself—AND it works!!!!
Yippee 😍
Does the washer have to be reset or recalibrated? Still doesnt start. Just lights up. No water runs either. Help.